Application Circuit
Modulazione
E - Modulazione con un'unità di controllo
- Ingresso: 4~20mA / 0~10V
- Uscita: 4~20mA / 0~10V
Dettagli di connessione:
- Collegare la linea di alimentazione CA 85-220V al terminale L e il neutro al terminale N.
- Collegamento della sorgente di segnale di ingresso 4-20mA/2-10V dal sistema di controllo all'ingresso-/+.
- Collegare l'uscita +/- al sistema per inviare la posizione della valvola in tempo reale.
On - Off
A - With 2 active end-position signal outputs
- Control actuator to open or close with K
- The output terminal of end-position OPEN/CLOSE will send out the event as a 220VAC active signal form when the end-position was reached.
Dettagli di connessione:
- Connecting AC85-220V supply power neutral to P1.
- Switch AC85-220V line to CLOSE(P2) to close the valve
- Switch AC85-220V line to OPEN(P3) to open the valve.
- P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
- P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
- Connect earth to P7.
B - With 2 passive end-position switche
- Control actuator to open or close with K
- The output terminal of end-position OPEN/CLOSE will send out the event as a passive signal form when the end-position was reached.
Dettagli di connessione:
- Connecting AC85-220V supply power neutral to P1.
- Switch AC85-220V line to CLOSE(P2) to close the valve
- Switch AC85-220V line to OPEN(P3) to open the valve.
- P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
- P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
- P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
- Connect earth to P7.
G - DC motor with 2 end-position switches
- Control actuator to open or close by the supply power direction between the terminal 1 and 2
- The output terminal of end-position OPEN/CLOSE will send out the event as a passive signal form when the end-position was reached.
Dettagli di connessione:
- Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
- Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
- P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
- P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
- P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
- Connect earth to P7.
English (UK) 
香港中文 
繁體中文 
English (Canada) 
English (South Africa) 
English (Australia) 
English (New Zealand) 
English 
Español de Puerto Rico 
Français du Canada 
Español de México 
Español de Chile 
Español de Colombia 
Español de Uruguay 
עִבְרִית 
Nederlands (België) 
Français de Belgique 
Eesti 
Latviešu valoda 
Lietuvių kalba 
Français 
Deutsch 
Norsk nynorsk 
Deutsch (Österreich) 
Slovenčina 
Deutsch (Schweiz) 
Italiano 
