Common faults & troubleshooting for Modulating Actuators

This guide applies to the modulating actuators of the DCL explosion-proof series, weather-proof series, and quick-turn series. The models are as follows: Weather-proof actuator: DCL-05, DCL-10, DCL-20, DCL-40, DCL-60, DCL-100, DCL-160, DCL-250Explosion-proof actuator: DCL-Ex05, DCL-Ex10, DCL-Ex20, DCL-Ex40, DCL-Ex60Quick-turn actuator: DCL-K05, DCL-K10, DCL-K20, DCL-K40, DCL-K100 Common Faults and Fault Exclusion Methods   Fault Possible Causes Fault […]

Common faults & troubleshooting for ON-OFF actuators

This guide applies to the switch-type actuators of the DCL explosion-proof series, standard series, and quick-open series. The models are as follows: Weather-proof Actuator: DCL-05, DCL-10, DCL-20, DCL-40, DCL-60, DCL-100, DCL-160, DCL-250Explosion-Proof Actuator: DCL-Ex05, DCL-Ex10, DCL-Ex20, DCL-Ex40, DCL-Ex60Quick-Turn Actuator: DCL-K05, DCL-K10, DCL-K20, DCL-K40, DCL-K100 Common Faults and Troubleshooting Methods   Fault Possible Causes Troubleshooting Methods […]

DCL Actuator Modbus Application Note

DCL actuators support the Modbus-RTU protocol. Referring to this application manual, you can connect DCL actuators to Modbus. Panel SF-LC/MB SF-ZC/MB 1. Interface Definition P1：220VAC NP2：220VAC LP3：4-20mA Input –P4：4-20mA Input+P5：4-20mA Output-P6：4-20mA Output+P7：RS485 AP8：RS485 B 2. Button Open: Used in setting mode. Press this button to open the actuator while release it to stop. Press Set […]

Types of Actuators and How to Choose the Right One

Actuators can be classified based on their driving method into the following categories: 1. Electric Actuators Electric actuators use an electric motor as the power source, converting electrical energy into mechanical motion to drive the valve. Advantages: ✔ Adjustable speed✔ High positioning accuracy✔ Large torque output Disadvantages: ✖ Thermal effects of the motor may trigger […]

How Humidity Reduces the Lifespan of Actuators (Electric Valves)?

Humidity is well known to cause damage to electronic components. One of the primary ways humidity reduces the lifespan of electric actuators is through ionic migration short circuits. 1. What is Ionic Migration Short Circuit? Ionic migration occurs when moisture and contaminants on a circuit board facilitate the movement of ions between conductors, leading to […]

What Does the S2 Duty Cycle Mean in Actuators (Electric Valves)?

Many people have questions about the S2 duty cycle in actuators or electric valves. What does it mean, and why is it defined this way? 1. The Origin of S1, S2, S3, and S6 Duty Cycles The S1, S2, S3, and S6 duty cycles originate from electric motor classifications, with a primary focus on thermal […]

האם ניתן להשתמש במפעילי DCL באזורים בגובה רב?

סביבות בגובה רב מציבות אתגרים ייחודיים שיכולים להשפיע על ביצועי המפעילים החשמליים של DCL. דוח זה מעריך את השימוש בהם בגובה של 3,000 מטר מעל פני הים. 1. כיצד גובה רב משפיע על מוצרים חשמליים ככל שהגובה עולה:✔ צפיפות האוויר ולחץ האוויר יורדים, מה שמוביל לחוזק בידוד נמוך יותר ולסיכון מוגבר לקריסה חשמלית.✔ יעילות הקירור יורדת, מה שגורם […]

Why Do Voltage Output Signals Oscillate in Certain Conditions?

  1. Voltage Signal Transmission Path As shown in Figure 1, a voltage signal transmission system consists of three key components: Negative feedback voltage output circuit Signal transmission cable Includes parasitic capacitance (C1) and parasitic inductance (L1), which depend on cable length and wiring layout. Input signal acquisition circuit May include a low-pass filter (L2, […]

How to Configure the ON-OFF Actuators with Position Transmitter?

1. Mechanical Installation 1. Mechanical Installation Refer to the “How to Install the Actuator onto the Valve” section to correctly install the actuator onto the valve and manually operate it to confirm proper functioning. Follow the guidelines in “How to Set the ON-OFF Electric Valve” to properly adjust the actuator’s electrical limits (close limit CLS […]

How to Set Up a Modulating Electric Valve?

1. Installing the Actuator onto the Valve Follow the installation instructions in “How to Install the Actuator onto the Valve” to correctly install the actuator on the valve. Confirm normal operation by manually testing the valve movement. 2. Adjusting the Mechanical Limits for Fully Closed Position Use the handwheel to move the valve to the […]