Technical Parameters

Explosion Proof Grade	Exd II CT4Gb
Power Supply	DC24V, AC110V, AC220V, AC380V
Standard Torque/Time	400m/30S
Optional Torque/Time	200Nm/15S, 400Nm/60S
Rotation Angle Range	Adjustable from 0 to 90 degrees
Motor Power/Current	DC24V: 70W/7.80A AC110V: 90W/1.12A AC220V: 90W/0.64A AC380V: 40W /0.29A
Control Circuit	Type A/B/C/D/E/F/G/H
Weight	9.5kg
Insulation Resistance	DC24V: 100MΩ/250VDC AC110V/AC220V/AC380V: 100MΩ/500VDC
Withstand Voltage	DC24V/AC24V: 500VAC for 1 minute
Water Proof Level	IP68
Installation	360 ° installation at any angle
Electrical Interface	2-M20x1.5 explosion-proof plug, users should install corresponding explosion-proof cable connectors according to the selected cable during use
Working Temperature	-20℃~+60℃
Optional Function	Dehumidification heater

Dimensions

E - Moduliavimas su valdymo bloku

Connecting Details:

F – Su padėties nustatymo įrenginiu

Connecting Details:

C - Su 1KΩ/500Ω potenciometru

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D – Su potenciometru ir galinės padėties grįžtamuoju ryšiu

Valdykite pavarą atidarymui arba uždarymui su K
Realaus laiko vožtuvo padėtis bus siunčiama kaip potenciometro varžos vertė.
Galinės padėties ATIDARYTA/UŽDARYTA išvesties gnybtas pasiųs įvykį pasyvaus signalo pavidalu, kai bus pasiekta galinė padėtis.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - Su 2 aktyviais galinės padėties signalo išėjimais

Valdykite pavarą atidarymui arba uždarymui su K
Galinės padėties ATIDARYTA/UŽDARYTA išvesties gnybtas išsiųs įvykį 220 V kintamosios srovės aktyvaus signalo forma, kai bus pasiekta galinė padėtis.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B - Su 2 pasyviais galinės padėties jungikliais

Valdykite pavarą atidarymui arba uždarymui su K
Galinės padėties ATIDARYTA/UŽDARYTA išvesties gnybtas pasiųs įvykį pasyvaus signalo pavidalu, kai bus pasiekta galinė padėtis.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

G - Nuolatinės srovės variklis su 2 galinės padėties jungikliais

Valdykite pavarą, kad ji atidarytų arba uždarytų maitinimo kryptį tarp 1 ir 2 gnybtų
Galinės padėties ATIDARYTA/UŽDARYTA išvesties gnybtas pasiųs įvykį pasyvaus signalo pavidalu, kai bus pasiekta galinė padėtis.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

H - 3 fazių 380 V kintamosios srovės variklis su 2 galinės padėties jungikliais

Išorinio keitiklio valdomas pavaros atidarymo arba uždarymo valdymas, siekiant pakeisti maitinimo fazę.
Galinės padėties ATIDARYTA/UŽDARYTA išvesties gnybtas pasiųs įvykį pasyvaus signalo pavidalu, kai bus pasiekta galinė padėtis.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Pastaba:

Punktyrinės dėžutės viduje esanti grandinė yra vidinė pavaros grandinė. O išorinė grandinė yra pavaros elektrinio prijungimo demonstracija.
Jei turite kitų specifinių reikalavimų dėl prijungimo grandinės, susisiekite su mūsų technine pagalba.