Technical Parameters

Power Supply	DC24V, AC24V, AC110V, AC220V, AC380V
Standard Torque/Time	600 Nm/45 s
Rotation Angle Range	Adjustable from 0 to 90 degrees
Motor power	DC24V：70W/6.04A AC24V：90W/6.80A AC110V：90W/1.18A AC220V：90W/0.6A AC380V：40W/0.29A
Control Circuit	Type A/B/C/D/E/F/G/H
Weight	10Kg
Insulation Resistance	DC24V/AC24V： 100MΩ/250VDC AC110V/AC220V/AC380V： 100MΩ/500VDC
Withstand Voltage	DC24V/AC24V: 500VAC for 1 minute
Water Proof Level	IP67
Installation	360 ° installation at any angle
Electrical Interface	G1/2 waterproof cable connector: one power line and one signal line each
Working Temperature	-25℃ ~ +55℃
Optional Function	Over torque protection, dehumidification heater, convex indicator, operating handwheel

Dimensions

E - Modulation mit einer Steuereinheit

Connecting Details:

F – Mit einer Positioniereinheit

Connecting Details:

C - Mit einem 1 kΩ/500 Ω Potentiometer

Steueraktuator zum Öffnen oder Schließen mit K
Die Ventilposition in Echtzeit wird als Widerstandswert des Potentiometers ausgegeben.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D – Mit Potentiometer und Endlagenrückmeldung

Steueraktuator zum Öffnen oder Schließen mit K
Die Ventilposition in Echtzeit wird als Widerstandswert des Potentiometers ausgegeben.
Der Ausgangsanschluss der Endposition OPEN/CLOSE sendet das Ereignis als passives Signal aus, sobald die Endposition erreicht ist.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - Mit 2 aktiven Endpositionssignalausgängen

Steueraktuator zum Öffnen oder Schließen mit K
Der Ausgangsanschluss der Endposition OPEN/CLOSE sendet das Ereignis als aktives 220VAC-Signal aus, sobald die Endposition erreicht ist.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B – Mit 2 passiven Endpositionsschaltern

Steueraktuator zum Öffnen oder Schließen mit K
Der Ausgangsanschluss der Endposition OPEN/CLOSE sendet das Ereignis als passives Signal aus, sobald die Endposition erreicht ist.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

G - Gleichstrommotor mit 2 Endschaltern

Der Stellantrieb wird durch die Richtung der Versorgungsspannung zwischen den Klemmen 1 und 2 zum Öffnen oder Schließen gesteuert.
Der Ausgangsanschluss der Endposition OPEN/CLOSE sendet das Ereignis als passives Signal aus, sobald die Endposition erreicht ist.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

H - 3-Phasen-380-V-Wechselstrommotor mit 2 Endschaltern

Der Stellantrieb wird mittels eines externen Wechselrichters gesteuert, um die Phase der Versorgungsspannung zu ändern und den Stellantrieb zu öffnen oder zu schließen.
Der Ausgangsanschluss der Endposition OPEN/CLOSE sendet das Ereignis als passives Signal aus, sobald die Endposition erreicht ist.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Notiz:

Der Schaltkreis im gestrichelten Kasten ist der interne Schaltkreis des Aktuators. Der Schaltkreis außerhalb des Kastens veranschaulicht die elektrische Verbindung zum Betrieb des Aktuators.
Falls Sie weitere spezielle Anforderungen an die Anschlussschaltung haben, wenden Sie sich bitte an unseren technischen Support.