{"id":6033,"date":"2023-08-03T20:44:54","date_gmt":"2023-08-03T12:44:54","guid":{"rendered":"https:\/\/www.dcl-controls.com\/?p=6033"},"modified":"2025-03-27T09:47:56","modified_gmt":"2025-03-27T09:47:56","slug":"dcl-02-on-off-actuator","status":"publish","type":"post","link":"https:\/\/dclcontrols.com\/pl_pl\/wsparcie\/mr-actuator\/dcl-02-on-off-actuator","title":{"rendered":"Typowe usterki i rozwi\u0105zywanie problem\u00f3w z si\u0142ownikami DCL-02 ON-OFF"},"content":{"rendered":"
\n\t\t\t\t
\n\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

This guide is applicable to the DCL Ultra-Small Series actuators, with the following models:<\/p>

  • DCL-02A<\/p><\/li>

  • DCL-02B<\/p><\/li>

  • DCL-02G<\/p><\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

    \n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"Szk\u0142o\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t

    Typowe usterki i metody rozwi\u0105zywania problem\u00f3w<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    \u00a0<\/p>
    Usterka<\/strong><\/th>Mo\u017cliwe przyczyny<\/strong><\/th>Troubleshooting Methods<\/strong><\/th><\/tr><\/thead>
    Actuator does not open or close on initial start<\/strong><\/td>1. Nieprawid\u0142owe okablowanie<\/td>Check the wiring according to the actuator\u2019s wiring diagram.<\/td><\/tr>
    \u00a0<\/td>2. Nieprawid\u0142owe zasilanie<\/td>Ensure the power supply voltage is within \u00b110% of the actuator\u2019s rated voltage and the current is 3 times the rated current.<\/td><\/tr>
    \u00a0<\/td>3. Faulty control switch or relay<\/td>Measure the input voltage at the actuator’s control terminal using a multimeter to verify it matches expectations.<\/td><\/tr>
    \u00a0<\/td>4. Niedopasowanie systemu sterowania<\/td>Test the actuator with a mechanical switch. If it operates normally, verify the control system’s output logic.<\/td><\/tr>
    \u00a0<\/td>5. Multiple actuators or actuators and other devices connected in parallel<\/td>Switch actuators should use single-path control and not be wired in parallel, as this affects the startup capacitor.<\/td><\/tr>
    Si\u0142ownik mo\u017ce tylko otwiera\u0107 lub zamyka\u0107<\/strong><\/td>1. Nieprawid\u0142owe okablowanie<\/td>Check the wiring using the actuator\u2019s wiring diagram.<\/td><\/tr>
    \u00a0<\/td>2. Incorrect full open\/close cam setting<\/td>Refer to the “How to Set Electric Switch-Type Valves” guide and correctly set the cam positions.<\/td><\/tr>
    Actuator stops in the middle of travel<\/strong><\/td>1. Valve jammed<\/td>Check for blockages in the valve. Clear any obstruction and retry after the actuator’s overload protection cools.<\/td><\/tr>
    \u00a0<\/td>2. Solid material in fluid causing valve jam<\/td>Inspect the fluid for solid particles causing valve jams. Clear the jam and retry after the actuator\u2019s overload protection cools.<\/td><\/tr>
    \u00a0<\/td>3. Incorrect full open\/close stopper setting<\/td>Refer to the “How to Set Electric Switch-Type Valves” guide and correctly adjust the stopper positions.<\/td><\/tr>
    Unable to turn actuator using the handle<\/strong><\/td>1. Solid material in fluid causing valve to seize<\/td>Check for blockage in the valve. Clear the blockage and retry after the actuator\u2019s overload protection cools.<\/td><\/tr>
    \u00a0<\/td>2. Valve seizing<\/td>Inspect the valve for jamming. Clear the blockage and retry after the actuator\u2019s overload protection cools.<\/td><\/tr>
    \u00a0<\/td>3. Damaged actuator reduction mechanism<\/td>Remove the actuator from the valve and rotate the handle. If it doesn\u2019t move, replace the actuator.<\/td><\/tr>
    No position feedback signal<\/strong><\/td>1. Incorrect wiring at the switch<\/td>Check the wiring according to the actuator\u2019s wiring diagram.<\/td><\/tr>
    \u00a0<\/td>2. Incorrect full open\/close cam setting<\/td>Refer to the “How to Set Electric Switch-Type Valves” guide and set the cam position correctly.<\/td><\/tr>
    \u00a0<\/td>3. Overcurrent causing position feedback switch damage<\/td>1. Check if the full open\/close cam is pressing on the position feedback switch correctly, as per the guide.<\/td><\/tr>
    \u00a0<\/td>\u00a0<\/td>2. Measure if the position feedback circuit is closed.<\/td><\/tr><\/tbody><\/table>

    \u00a0<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

    \n\t\t\t\t
    \n\t\t\t\t\t

    Verify that the operating conditions meet the parameter requirements.<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    Electric actuators may fail due to improper use or being used in incorrect operating conditions. When used within the operating conditions defined in the product specifications, the actuator can be expected to operate reliably for an extended period without failure.<\/p>

    • Supply Voltage:<\/strong> The voltage from the power supply must be within the rated operating voltage range of the actuator. Overvoltage or undervoltage may shorten the actuator’s lifespan.<\/p><\/li>

    • Supply Current:<\/strong> The starting current of the motor is significantly higher than the rated current. To ensure reliable operation, use a power supply capable of delivering at least 3 times the rated current of the actuator.<\/p><\/li>

    • Temperatura:<\/strong> Ensure the actuator operates within its rated temperature range. Using the actuator outside this range may result in poor performance, reduced lifespan, and eventual failure.<\/p><\/li>

    • \u015arodowisko:<\/strong> The DCL switch-type actuator has an IP67 weatherproof rating, making it suitable for both indoor and outdoor applications. It offers a degree of protection against rain and splashing water, helping to prolong the actuator\u2019s life by shielding it from rain, snow, ice, and UV (sunlight). However, in highly corrosive environments, electronic components may fail prematurely. Non-explosion-proof actuators should not be used in explosive environments.<\/p><\/li>

    • Duty Cycle:<\/strong> The DCL switch-type actuator has a duty cycle of 70% (42 seconds of operation per minute, followed by 18 seconds of rest). Exceeding this duty cycle may cause the motor to enter thermal protection.<\/p><\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

      \n\t\t\t\t
      \n\t\t\t\t\t

      Sprawd\u017a okablowanie si\u0142ownika<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
      \n\t\t\t\t
      \n\t\t\t\t\t\t\t\t\t

      Ensure the actuator is wired correctly according to the wiring diagram provided by the manufacturer. Follow these steps to verify the wiring:<\/p>

      1. Power Supply:<\/strong><\/p>

        • Check the power supply connections to ensure they match the actuator’s required input voltage and current.<\/p><\/li><\/ul><\/li>

        • Control Connections:<\/strong><\/p>

          • Verify that the input and output control connections are securely attached and in the correct configuration as per the actuator\u2019s wiring diagram.<\/p><\/li><\/ul><\/li>

          • Signal Wiring:<\/strong><\/p>

            • Check the wiring for control signals, such as 4-20mA or 0-10V, depending on the actuator\u2019s specifications.<\/p><\/li>

            • Confirm that there are no loose connections or short circuits.<\/p><\/li><\/ul><\/li>

            • Grounding:<\/strong><\/p>

              • Ensure that the actuator is properly grounded to prevent electrical interference or damage.<\/p><\/li><\/ul><\/li>

              • Connections to Other Equipment:<\/strong><\/p>

                • If the actuator is connected to other devices, make sure those connections are also correct and do not cause interference or power issues.<\/p><\/li><\/ul><\/li><\/ol>

                  If the wiring appears correct, but the actuator is still malfunctioning, further troubleshooting or assistance from a technician may be necessary.<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

                  \n\t\t\t\t\t
                  \n\t\t\t\t
                  \n\t\t\t\t
                  \n\t\t\t\t\t\t\t
                  \n\t\t\t\t\t
                  \n\t\t\t
                  \n\t\t\t\t\t
                  \n\t\t
                  \n\t\t\t\t
                  \n\t\t\t\t
                  \n\t\t\t\t\t

                  A - Z 2 aktywnymi wyj\u015bciami sygna\u0142u po\u0142o\u017cenia kra\u0144cowego<\/p>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

                  \n\t\t\t\t
                  \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"DCL\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
                  \n\t\t\t\t
                  \n\t\t\t\t\t\t\t\t\t
                  • Si\u0142ownik steruj\u0105cy do otwierania lub zamykania za pomoc\u0105 K<\/li>
                  • Wyj\u015bcie terminala kra\u0144cowego po\u0142o\u017cenia OTWARTE\/ZAMKNI\u0118TE wy\u015ble zdarzenie jako aktywny sygna\u0142 220VAC w momencie osi\u0105gni\u0119cia po\u0142o\u017cenia kra\u0144cowego.<\/li><\/ul>

                    \u00a0<\/p>

                    Szczeg\u00f3\u0142y po\u0142\u0105czenia:<\/strong><\/p>

                    1. Pod\u0142\u0105czenie przewodu neutralnego zasilania AC85-220V do P1.<\/li>
                    2. Prze\u0142\u0105cz lini\u0119 AC85-220V na CLOSE(P2), aby zamkn\u0105\u0107 zaw\u00f3r<\/li>
                    3. Prze\u0142\u0105cz lini\u0119 AC85-220V na pozycj\u0119 OTWARTE (P3), aby otworzy\u0107 zaw\u00f3r.<\/li>
                    4. P5 to zacisk kra\u0144cowego po\u0142o\u017cenia OTWARTE, kt\u00f3ry wyprowadza pr\u0105d zmienny o napi\u0119ciu 220 V, kt\u00f3ry mo\u017cna wykorzysta\u0107 do zasilania lampki sygnalizacyjnej, gdy si\u0142ownik osi\u0105gnie kra\u0144cowe po\u0142o\u017cenie otwarte.<\/li>
                    5. P6 to zacisk kra\u0144cowego po\u0142o\u017cenia OTWARTE, kt\u00f3ry wyprowadza pr\u0105d zmienny o napi\u0119ciu 220 V, kt\u00f3ry mo\u017cna wykorzysta\u0107 do zasilania lampki sygnalizacyjnej, gdy si\u0142ownik osi\u0105gnie po\u0142o\u017cenie kra\u0144cowe zamkni\u0119cia.<\/li>
                    6. Pod\u0142\u0105cz uziemienie do P7.<\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
                      \n\t\t\t\t
                      \n\t\t\t\t
                      \n\t\t\t\t\t

                      B - Z 2 pasywnymi wy\u0142\u0105cznikami kra\u0144cowymi<\/p>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

                      \n\t\t\t\t
                      \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"DCL\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
                      \n\t\t\t\t
                      \n\t\t\t\t\t\t\t\t\t
                      • Si\u0142ownik steruj\u0105cy do otwierania lub zamykania za pomoc\u0105 K<\/li>
                      • Wyj\u015bcie terminala kra\u0144cowego po\u0142o\u017cenia OTWARTE\/ZAMKNI\u0118TE wy\u015ble zdarzenie jako sygna\u0142 pasywny po osi\u0105gni\u0119ciu po\u0142o\u017cenia kra\u0144cowego.<\/li><\/ul>

                        \u00a0<\/p>

                        Szczeg\u00f3\u0142y po\u0142\u0105czenia:<\/strong><\/p>

                        1. Pod\u0142\u0105czenie przewodu neutralnego zasilania AC85-220V do P1.<\/li>
                        2. Prze\u0142\u0105cz lini\u0119 AC85-220V na CLOSE(P2), aby zamkn\u0105\u0107 zaw\u00f3r<\/li>
                        3. Prze\u0142\u0105cz lini\u0119 AC85-220V na pozycj\u0119 OTWARTE (P3), aby otworzy\u0107 zaw\u00f3r.<\/li>
                        4. P4 to z\u0142\u0105cze COM dla sygna\u0142u pasywnego styku po\u0142o\u017cenia kra\u0144cowego OTWARTY\/ZAMKNI\u0118TY, kt\u00f3re normalnie jest pod\u0142\u0105czone do sygna\u0142u GND.<\/li>
                        5. P5 to zacisk kra\u0144cowego po\u0142o\u017cenia OTWARTE, kt\u00f3ry zostanie pod\u0142\u0105czony do COM, gdy si\u0142ownik osi\u0105gnie kra\u0144cowe po\u0142o\u017cenie otwarte.<\/li>
                        6. P6 to zacisk po\u0142o\u017cenia kra\u0144cowego ZAMKNI\u0118CIA, kt\u00f3ry zostanie pod\u0142\u0105czony do COM, gdy si\u0142ownik osi\u0105gnie po\u0142o\u017cenie kra\u0144cowe zamkni\u0119cia.<\/li>
                        7. Pod\u0142\u0105cz uziemienie do P7.<\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
                          \n\t\t\t\t
                          \n\t\t\t\t
                          \n\t\t\t\t\t

                          G - Silnik pr\u0105du sta\u0142ego z 2 wy\u0142\u0105cznikami kra\u0144cowymi<\/p>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

                          \n\t\t\t\t
                          \n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"DCL\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
                          \n\t\t\t\t
                          \n\t\t\t\t\t\t\t\t\t
                          • Si\u0142ownik steruj\u0105cy do otwierania lub zamykania za pomoc\u0105 kierunku zasilania pomi\u0119dzy zaciskami 1 i 2<\/li>
                          • Wyj\u015bcie terminala kra\u0144cowego po\u0142o\u017cenia OTWARTE\/ZAMKNI\u0118TE wy\u015ble zdarzenie jako sygna\u0142 pasywny po osi\u0105gni\u0119ciu po\u0142o\u017cenia kra\u0144cowego.<\/li><\/ul>

                            \u00a0<\/p>

                            Szczeg\u00f3\u0142y po\u0142\u0105czenia:<\/strong><\/p>

                            1. Pod\u0142\u0105cz DC24V+ do P1 i DC24V- do P2, aby zamkn\u0105\u0107 zaw\u00f3r.<\/li>
                            2. Pod\u0142\u0105cz DC24V+ do P2 i DC24V- do P1, aby zamkn\u0105\u0107 zaw\u00f3r.<\/li>
                            3. P3 to COM dla sygna\u0142u pasywnego styku po\u0142o\u017cenia kra\u0144cowego OTWARTY\/ZAMKNI\u0118TY, kt\u00f3ry normalnie jest pod\u0142\u0105czony do sygna\u0142u GND.<\/li>
                            4. P4 to zacisk kra\u0144cowego po\u0142o\u017cenia OTWARTE, kt\u00f3ry zostanie pod\u0142\u0105czony do COM, gdy si\u0142ownik osi\u0105gnie kra\u0144cowe po\u0142o\u017cenie otwarte.<\/li>
                            5. P5 to zacisk po\u0142o\u017cenia kra\u0144cowego ZAMKNI\u0118CIA, kt\u00f3ry zostanie pod\u0142\u0105czony do COM, gdy si\u0142ownik osi\u0105gnie po\u0142o\u017cenie kra\u0144cowe zamkni\u0119cia.<\/li>
                            6. Pod\u0142\u0105cz uziemienie do P7.<\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
                              \n\t\t
                              \n\t\t\t\t
                              \n\t\t\t\t
                              \n\t\t\t\t\t\t\t\t\t

                              Uwaga\uff1a<\/p>

                              • Obw\u00f3d wewn\u0105trz przerywanej ramki to wewn\u0119trzny obw\u00f3d si\u0142ownika. Natomiast obw\u00f3d na zewn\u0105trz to demonstracja po\u0142\u0105czenia elektrycznego do korzystania z si\u0142ownika.<\/li>
                              • Je\u015bli masz inne specyficzne wymagania dotycz\u0105ce obwodu po\u0142\u0105czeniowego, skontaktuj si\u0119 z naszym dzia\u0142em pomocy technicznej.\u00a0<\/li><\/ul>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
                                \n\t\t\t\t
                                \n\t\t\t\t\t\t\t\t\t

                                When conducting troubleshooting on-site, feel free to contact our technical service personnel immediately for assistance in diagnosing and resolving the issue.
                                Contact phone number: 13026331611 (Mr. Chen)<\/p>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>","protected":false},"excerpt":{"rendered":"

                                Niniejsza instrukcja dotyczy si\u0142ownik\u00f3w serii DCL Ultra-Small w nast\u0119puj\u0105cych modelach: DCL-02A DCL-02B DCL-02G Typowe usterki i metody rozwi\u0105zywania problem\u00f3w Usterka Mo\u017cliwe przyczyny Metody rozwi\u0105zywania problem\u00f3w Si\u0142ownik nie otwiera si\u0119 lub nie zamyka przy pierwszym uruchomieniu 1. Nieprawid\u0142owe okablowanie Sprawd\u017a okablowanie zgodnie ze schematem elektrycznym si\u0142ownika. 2. Nieprawid\u0142owe zasilanie Upewnij si\u0119, \u017ce [...]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"elementor_theme","format":"standard","meta":{"_acf_changed":true,"footnotes":""},"categories":[103],"tags":[53],"class_list":["post-6033","post","type-post","status-publish","format-standard","hentry","category-mr-actuator","tag-actuator"],"acf":[],"_links":{"self":[{"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/posts\/6033","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/comments?post=6033"}],"version-history":[{"count":0,"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/posts\/6033\/revisions"}],"wp:attachment":[{"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/media?parent=6033"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/categories?post=6033"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/dclcontrols.com\/pl_pl\/wp-json\/wp\/v2\/tags?post=6033"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}